We only print models for which we have an active commercial licence.
RPG Dice Set Kit Card | Build Your Own 7-Piece Dice Set
£5.00
Skip to product information
£5.00
20+ years online
5000+ positive eBay feedback
Dispatched from Scotland
Checked, stored and dispatched by BlueCyborg from our Scottish premises — no dropshipping.
Roll for creativity with this clever build-your-own RPG dice kit card, designed by Tjoene and 3D printed by BlueCyborg.
All the pieces needed to assemble a complete seven-piece polyhedral dice set are contained within one compact card: D20, D12, D10 numbered 0 to 9, percentile D10 numbered 00 to 90, D8, D6 and D4.
Carefully detach the pieces from the frame, then slot them together to create your own set of playable RPG dice. No glue is required.
Measuring approximately 15.7 × 10.6 cm, the kit card is compact enough to slip inside many greeting cards, making it a wonderfully unusual gift for tabletop roleplayers, dice collectors and puzzle lovers.
A colourful surprise
Every kit card is printed in its own colour combination. Because many combinations are unique and may never be repeated, online orders are supplied in a randomly selected colour.
The photographs show examples of the colours you might receive. Your kit card may be a different colour or combination from those pictured. We think the surprise is part of the fun!
Please note
You will receive one unassembled kit card. The assembled dice and empty frame shown in some photographs are for demonstration only.
Colours are selected at random and cannot be requested. Small variations and visible layer lines are normal characteristics of 3D-printed products. Carefully trim any remaining attachment points if necessary.
Contains small parts. Keep away from young children.
These 3D-printed dice may not have the precision balance of commercially manufactured gaming dice.
Designed by Tjoene and produced for sale under a commercial licence.
Assembly Instructions
No glue required.
The joints of the pieces feature a slight dovetail design and require a bit of pressure to push into place. Once assembled, it is not recommended to disassemble them again.
D20
- Carefully remove each piece from the frame.
- Gently bend the faces of the top piece (4-18) inward, and connect the 4-face to the 18-face. Repeat this for the bottom piece (8-16), connecting the 8-face to the 16-face.
- Gently bend the faces of the middle piece inward.
- Connect the 4- and 18-face of the top piece and the middle piece, with the 4-face aligned to the 14-face and the 18-face aligned to the 2-face. Don't connect the other faces just yet.
- Connect the 16- and 8-face of the bottom piece and the middle piece, with the 16-face aligned to the 6-face and the 8-face aligned to the 20-face.
- Go around and connect the remaining faces. For the last faces, the 1-face and 7-face, lift the top or bottom piece slightly so it can snap into place. The 1- and 7-face each have a small edge that clips behind the top and bottom piece to keep them from detaching. For the 7-face, slightly lift the connecting bottom piece with the 17-face. For the 1-face, slightly lift the connecting top piece with the 13-face.
And there you have your new D20!
D12
- Carefully remove each piece from the frame.
- Gently bend the long face pieces into shape.
- Slide the 4-face of the die into the grooves of the 3- and 8-face.
- Then go around connecting the other faces of the top and bottom part.
- Place the 12-face on the top, aligned with the 9-face as shown below.
- Place the 1-face on the bottom, aligned with the 4-face as shown below.
And there you have your new D12!
D10
- Carefully remove each piece from the frame.
- Gently bend the faces of the pieces inward.
- Connect the 4-face to the 7-face as shown below so the 1-face will connect to the 1- and 7-face.
- Push the 1-face into place, then the 6-face and so on, alternating between the faces of the upper and lower part.
And there you have your new D10!
D00
- Carefully remove each piece from the frame.
- Gently bend the faces of the pieces inward.
- Connect the 40-face to the 70-face as shown below so the 10-face will connect to the 10- and 70-face.
- Push the 10-face into place, then the 60-face and so on, alternating between the faces of the upper and lower part.
And there you have your new percentile D10!
D8
- Carefully remove each piece from the frame.
- Gently bend the faces of the pieces inward.
- Flatten the pieces and connect the 4-face to the 1-face, then go around connecting the other faces.
And there you have your new D8!
D6
- Carefully remove each piece from the frame.
- Gently bend the faces of the long piece inward and connect the ends.
- Connect the 1-face aligned to the 2-face as shown below.
- Connect the 6-face aligned to the 5-face as shown below.
And there you have your new D6!
D4
- Carefully remove each piece from the frame.
- Gently bend the faces of both pieces inward.
- Move both pieces into each other as shown below. Connect one side first, then the other, making sure the numbers in the corners align.
And there you have your new D4!
Reviews
Shipping & Returns
Orders we dispatch ourselves leave from our Scottish premises. Delivery options and estimates are shown at checkout. We currently cannot ship to EU countries or Northern Ireland.
If something isn’t right with your order, contact us and we’ll help put it right.
Authorised Seller
Product Safety
At BlueCyborg, we prioritise your safety. All our products are intended for use as described and should be kept out of reach of young children unless otherwise stated. Small parts may pose a choking hazard. Always use items with care and in a suitable environment. If you have any questions about safe usage, please don’t hesitate to contact us.
This product is not a toy and is intended for ages 14+.
- Not suitable for children under 3 years – small parts may pose a choking hazard.
- Keep away from heat sources – may deform under high temperatures.
- Use responsibly – designed for stress relief, not excessive force or impact.
- Complies with UKCA safety standards for consumer goods.
Our resin miniatures are designed for hobby use by adults and older children under adult supervision. Resin dust can be harmful if inhaled, so always wear a suitable mask and work in a well-ventilated area when sanding, drilling, or cutting resin parts. Avoid contact with eyes and mouth, and wash hands thoroughly after handling.
Please note that uncured resin is toxic and should never come into contact with skin or be ingested. At BlueCyborg, we take every precaution to ensure all our resin miniatures are fully cured before they reach you, but care should always be taken when working with resin components.
These miniatures are not toys and may contain small or sharp parts that can pose a choking or injury hazard. Keep out of reach of young children.
Always follow safety precautions when assembling, modifying, or painting resin miniatures. If skin irritation or other symptoms occur, discontinue use and seek medical advice.